VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit CBD with spec sheet
starter vape kits · smoke shop owners

Starter Vape Kit CBD with spec sheet

This page is for smoke shop owners who want a working answer on specification, price and lead time before they commit a purchase order. We have written the detail down so nobody has to sit through a sales call to extract it.

Published 20 August 2026  ·  VapeWholesaleHub  ·  Reading time 8 min

Starter Vape Kit CBD with spec sheet configuration from a production run, photographed before packing.
Starter Vape Kit CBD with spec sheet configuration from a production run, photographed before packing.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.

Reading a quotation properly

A starter vape kit programme only works when three numbers agree: your shelf price, your reorder cycle and your defect tolerance. Change one and the plan moves. We build assortments around those three and we say so up front rather than after the invoice.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

We publish a realistic band of 2.96 to 8.42 per unit for standard configurations at 500 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

What a sensible opening order looks like

We keep a short list of approved configurations for starter vape kits. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

A practical starting order for smoke shop owners is 500 units across two or three SKUs, not 500 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

For smoke shop owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Quality control, in plain terms

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

  • Reference sample retained from every batch
  • Consolidated or split shipping, quoted both ways
  • Standing reorder schedule with a fixed cut-off
  • Document pack prepared per destination market
  • Mixed SKU cartons to spread first-order risk
  • Cartons drop-tested and pallet-counted for clean freight

Labels, closures and traceability

Artwork approval is a two stage process: a digital proof for text and layout, then a physical dummy for colour and finish. Skipping the dummy is the single most common cause of a reprint.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.0 ml
Coil resistance1.0 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order200 units per SKU, mixed cartons allowed
Lead time25 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

What is the minimum order for starter vape kit?

Standard configurations start at 500 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 1000 units because of setup time on the line.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us